Search found 42 matches

by Firefly
Sat Feb 10, 2018 3:30 pm
Forum: Duet Wifi & Ethernet
Topic: over-powered message.
Replies: 5
Views: 1368

over-powered message.

I have a message that appears on the Duet WiFi PanelVue Console page , it says: Heater 1 appears to be over-powered. If left at full power, its temperature is predicted.

what does this mean? and is there any concern?
by Firefly
Thu Feb 08, 2018 7:28 pm
Forum: Print Defects
Topic: Layers get bad & extruder clicking
Replies: 5
Views: 703

Re: Layers get bad & extruder clicking

I got same issue, but I did feel it binding when thumbing the big feed gear, soon as I loosen the one bolt with star washer holding the heat sink it freed up, I think as it warms up it got too tight.
by Firefly
Wed Feb 07, 2018 7:49 pm
Forum: Frame Assembly
Topic: Top triangle mounting
Replies: 3
Views: 619

Re: Top triangle mounting

My kit is on the way and I have been overlooking the build guide. I was wondering why the top triangle isn't flush with the end of the towers like the bottom triangle. Seems it would be easier to build, that is if the towers are all the same length. if you got the 'Plus' see my notes here: https://...
by Firefly
Wed Feb 07, 2018 11:38 am
Forum: General Discussion
Topic: General overview video
Replies: 2
Views: 867

Re: General overview video

web console with print job running: https://youtu.be/_jMePbcEBcY
Panel Vue: https://youtu.be/R_hg1ILg9Rg
by Firefly
Wed Feb 07, 2018 10:38 am
Forum: General Discussion
Topic: General overview video
Replies: 2
Views: 867

Re: General overview video

I haven't done any jogging with it, but I do love the DuetWifi, so easy to use and also can control & watch it via webpage. I will try to get a few shots for you.
by Firefly
Mon Feb 05, 2018 10:46 am
Forum: Enclosure Designs...
Topic: D300vs Plus enclosure
Replies: 5
Views: 1440

Re: D300vs Plus enclosure

I am getting back into this project, I happened to have a couple big sheets of thin chloroplast for back sides. I cut one side of flute where I want it to bend, and able to wrap around the back in one piece. I made this clips that fit in the upper extrusion of bottom frame for the chloroplast to sit...
by Firefly
Sun Jan 14, 2018 6:51 pm
Forum: GCODE
Topic: Gcode for prime line not working after upgrading to 1.19
Replies: 10
Views: 2187

Re: Gcode for prime line not working after upgrading to 1.19

It works in Simplify3d but when I tried the code in Slic3r for Prusa, it doesn't wait for Hotend to warm up.
it does the prime line then waits for hotend to warm up, any ideas?
by Firefly
Fri Jan 12, 2018 5:25 pm
Forum: Electronics Wiring
Topic: Panel Due Wiring
Replies: 2
Views: 700

Re: Panel Due Wiring

Or you can put it through the center of the 20x40, it fits with the connector.
Yes I have mine this way.
by Firefly
Fri Jan 05, 2018 5:04 pm
Forum: Enclosure Designs...
Topic: D300vs Plus enclosure
Replies: 5
Views: 1440

Re: D300vs Plus enclosure

3.PNG
wood or 3d printed ends?
by Firefly
Fri Jan 05, 2018 5:04 pm
Forum: Enclosure Designs...
Topic: D300vs Plus enclosure
Replies: 5
Views: 1440

D300vs Plus enclosure

D300vs Plus enclosure in planning stage at this time.

figured out the wheels on the carriage won't hit a panel when laid flat against the top and bottom rails.
got some experimenting to do, also looking at a heat shield with about 1 cm space under the heatbed.
1.PNG
2.PNG
2.PNG (81.45 KiB) Viewed 1440 times
4.PNG