Search found 12 matches

by AE9RB
Wed Jan 10, 2018 8:23 pm
Forum: Slicers
Topic: Simplify3D profile Mk3
Replies: 1
Views: 677

Simplify3D profile Mk3

This is a Simplify3D profile that makes your D300VS print at the same speed a the new Prusa i3 Mk3. Why? The Mk3 has 24V software-controlled Trinamic drivers too. It's fast enough that they were able tune movements a Mk2 couldn't handle but are easy for a modest delta. I liked the results enough to ...
by AE9RB
Sat Jan 06, 2018 6:54 pm
Forum: D300VS-PLUS Upgrade
Topic: Tricklaser Ball Cup Arm Length Question
Replies: 3
Views: 781

Re: Tricklaser Ball Cup Arm Length Question

After further testing it turns out 375.0 for my arms marked 375.0 gives me the right size prints.
by AE9RB
Fri Dec 22, 2017 2:31 am
Forum: D300VS-PLUS Upgrade
Topic: Volcano Mk3
Replies: 1
Views: 299

Volcano Mk3

I put a volcano heatblock on my plus. Upgraded the cooler with a part from a Prusa i3 Mk3. Printed out the parts in genuine Prusa orange ABS just to be silly. It's on thingiverse to download.
https://www.thingiverse.com/thing:2725946
20171222_064325311_iOS.jpg
by AE9RB
Tue Dec 19, 2017 12:42 pm
Forum: D300VS-PLUS Upgrade
Topic: Tricklaser Ball Cup Arm Length Question
Replies: 3
Views: 781

Re: Tricklaser Ball Cup Arm Length Question

My arms, all marked 375.0, calibrated to:

Code: Select all

M665 L376.4
by AE9RB
Sat Dec 16, 2017 7:05 pm
Forum: D300VS-PLUS Upgrade
Topic: PT100 stability
Replies: 1
Views: 395

PT100 stability

I finally got around to tracking down and fixing a PT100 annoyance while installing the plus parts. Chopper drivers at 24V make quite a bit of electrical noise. PT100 circuits are very sensitive to this type of noise. Fortunately, it's cheap and easy to fix. Get a USB 2.0 cable. When you cut it open...
by AE9RB
Sun May 21, 2017 9:21 am
Forum: Calibration
Topic: ~~~ Stringing
Replies: 17
Views: 2087

Re: ~~~ Stringing

Everything I'm ready to share for your printer is posted here: https://www.thingiverse.com/thing:2223113
There's a Cura profile which will give you similarly good results.
by AE9RB
Sun May 21, 2017 12:43 am
Forum: Calibration
Topic: FSR pads slipping
Replies: 6
Views: 664

FSR pads slipping

IMG_0116.JPG
oops. All three migrated like this.
by AE9RB
Sun May 21, 2017 12:10 am
Forum: Calibration
Topic: ~~~ Stringing
Replies: 17
Views: 2087

Re: ~~~ Stringing

Here's what Simplify3D can really do. I apologize for the change in lighting. IMG_0121.JPG This is the Simplify3D default settings with a minimal set of changes to describe the D300VS. You can see the infill bonds with the inner perimeter and the inner and outer perimeters are bonded. Also, less and...
by AE9RB
Sat May 20, 2017 10:08 pm
Forum: Calibration
Topic: ~~~ Stringing
Replies: 17
Views: 2087

Re: ~~~ Stringing

Brad's gcode on my D300VS with Micro extruder. IMG_0115.JPG Looks like normal stringing for these settings. The horrible infill is bad settings from the Rostock-derived S3D profile. It's like they changed every setting to give you the worst possible experience. I assure you the Micro can print much ...
by AE9RB
Sat May 20, 2017 5:25 pm
Forum: UMBEE
Topic: Shapeways UBMEE Main Body: Serious Droopage; So Sad
Replies: 17
Views: 2251

Re: Shapeways UBMEE Main Body: Serious Droopage; So Sad

Nah, I got the last one a couple days ago. They reprinted mine and it's fine. I'll know for sure when I actually build it (so don't ask for my not-broken-as-bad-as-yours yet). Also, I'll be selling a fully built and tested Umbee once my Aero design is complete.