Search found 29 matches

by garyd9
Mon Nov 05, 2018 9:11 pm
Forum: Extruder Assembly
Topic: Part cooling fan duct - step file?
Replies: 0
Views: 31

Part cooling fan duct - step file?

Brad, is there a .step file available for the D300VS+ part cooling fan duct? I've tried re-meshing the STL file in fusion360, but the results are less than ideal.

Thanks
Gary
by garyd9
Sun Oct 28, 2018 1:56 pm
Forum: Duet Wifi & Ethernet
Topic: Avoid Paneldue 1.22
Replies: 1
Views: 763

Re: Avoid Paneldue 1.22

The babystep popups are resolved in 1.22.1, but the rest of the trivial and obvious popups are still there. I begged dc42 to cut that new "feature" but it's still there. If you want a version of paneldue firmware without that extremely annoying "feature", let me know which paneldue firmware file you...
by garyd9
Mon Oct 22, 2018 2:36 pm
Forum: Calibration
Topic: FSR pads slipping
Replies: 7
Views: 1045

Re: FSR pads slipping

Good to know! My pads slip. I often reposition them. I will try CA soon :) I know it's an old thread, but wanted to catch anyone (like myself) who found it in a search. Don't use CA glue on FSR's. I've done it for the same reasons mentioned in this thread, and I've found that one of my FSR's is act...
by garyd9
Mon Oct 22, 2018 2:32 pm
Forum: Calibration
Topic: [Solved] Calibration deviation too high
Replies: 16
Views: 2025

Re: [Solved] Calibration deviation too high

Quick update... I mentioned in this thread that I used superglue to keep the pads on my FSR's. After further experience that resulted in some research, I've found that using CA glue on FSR's is a Bad Idea. If will "degrade the substrate and can lead to cracking." (I also believe that when the CA dri...
by garyd9
Sat Oct 20, 2018 12:53 am
Forum: Calibration
Topic: [Solved] Calibration deviation too high
Replies: 16
Views: 2025

Re: [Solved] Calibration deviation too high

Couldn't sleep, back to messing with 3d printer. Yes I put it back to S6. I thought the S7 suppose to be more accurate. just did the auto calibration few time and M500, will do some test prints tomorrow. ever mess with the Mesh Grid compensation/heightmap? just curious I know about not being able t...
by garyd9
Fri Oct 19, 2018 10:40 pm
Forum: Calibration
Topic: [Solved] Calibration deviation too high
Replies: 16
Views: 2025

Re: [Solved] Calibration deviation too high

0.1mm is a significant change for 3d printing. At a typical .2mm layer height, that's a full half layer.

In your bed.g, is the last G30 line set back to use "S6"? Do a few auto delta calibrations (G32) to get the deviation down. Once it comes down (and stays down), M500 to save it all.
by garyd9
Fri Oct 19, 2018 10:14 pm
Forum: Calibration
Topic: [Solved] Calibration deviation too high
Replies: 16
Views: 2025

Re: [Solved] Calibration deviation too high

Oh, and I really hope you have better luck than I've been having. I have everything set up perfectly (as far as I know) and I've been getting this weirdness where the duet would auto-calibrate to a situation where the nozzle would be too high (by about 0.05mm) at x0 y0, and then closer to "good" as ...
by garyd9
Fri Oct 19, 2018 9:25 pm
Forum: Calibration
Topic: [Solved] Calibration deviation too high
Replies: 16
Views: 2025

Re: [Solved] Calibration deviation too high

Take backups of config.g, bed.g and config-override.g Then delete config-override.g (or at least get rid of the G31 lines in it.) On the last G30 in bed.g, it should be S6. S7 is explicitly discouraged unless you have probe points that cause the delta arms to go nearly horizontal (and have a massive...
by garyd9
Fri Oct 19, 2018 10:20 am
Forum: Calibration
Topic: [Solved] Calibration deviation too high
Replies: 16
Views: 2025

Re: [Solved] Calibration deviation too high

Each of the bed probe heights is telling you how far the nozzle is "pressing" (from a Z0) in order to get the FSR/JohnSL board to show a trigger. Assuming that your bed.g has the center (x0 y0) last, the first oddity is that your underbed FSR's are triggering at a Z height greater than 0. (With unde...
by garyd9
Tue Oct 16, 2018 11:43 am
Forum: Electronics Wiring
Topic: Stepper motor wiring...
Replies: 0
Views: 1157

Stepper motor wiring...

I'm posting this in response to someone on the facebook group looking for help with stepper wiring. (FB keeps deleting every reply I make with any URL link...) For information on determining how to wire a stepper to the duet board, take a look here: https://duet3d.dozuki.com/Wiki/Choosing_and_connec...