Search found 14 matches

by Lucidwolf
Wed Nov 07, 2018 6:11 am
Forum: Cooling
Topic: Current state of cooling
Replies: 10
Views: 1356

Re: Current state of cooling

Well i got my fans in the mail a week ago. The Dii cooler is doing a pretty good job. I had to shim part of the bracket to get the angle right so the cooler sits level at the right height. I still have to slow down to 30m/s on extreme overhangs, but that is not usually much of the print so it doesn'...
by Lucidwolf
Sun Oct 21, 2018 8:59 am
Forum: Cooling
Topic: Current state of cooling
Replies: 10
Views: 1356

Re: Current state of cooling

That's good to hear.
I am still waiting for my fans... so I have not been able to continue experimenting.
by Lucidwolf
Tue Oct 16, 2018 7:46 am
Forum: Cooling
Topic: Current state of cooling
Replies: 10
Views: 1356

Re: Current state of cooling

Unfortunately 8.5mm puts the lower fastener in the same plane as the support web if mounting from the current attach point. Good news a 8.5mm shim was easy to model. Just a cube and some holes. The 8.5mm shim is on the thingiverse page. Put it between the bracket and the cooler. Will need longer scr...
by Lucidwolf
Sun Oct 14, 2018 11:37 pm
Forum: Cooling
Topic: Current state of cooling
Replies: 10
Views: 1356

Re: Current state of cooling

I uploaded the bracket I use to attach the Diii cooler since my cobbling the 40mm fan to it seemed to be the best design and gave access to the manual feed. Although now with a good hob i don't know how important that manual feed is anymore. I can respect the decision to cover it up. I think I wante...
by Lucidwolf
Sun Oct 14, 2018 10:31 am
Forum: Enclosure Designs...
Topic: Enclosure Design Questions
Replies: 0
Views: 825

Enclosure Design Questions

Greetings, I am starting my enclosure design but wanted to make sure I have the exact dimensions. I am measuring the horizontal v slots at 455mm and the vertical v slots at 1000 mm. Is this correct? (Was expecting 500mm and 1000mm) <Edit: typo> Also is there a step file of the upper corner bracket? ...
by Lucidwolf
Fri Oct 12, 2018 3:57 am
Forum: Cooling
Topic: Current state of cooling
Replies: 10
Views: 1356

Current state of cooling

Greetings, I am curious if anyone else has experimented with the cooling on the Titan Aero? Trying to get ideas as I wait on my blower fans in the snail mail. I am trying to get my layer time down to less that 30 seconds while still having good overhang and reduced curling. The goal is to get good q...
by Lucidwolf
Mon Oct 01, 2018 11:06 am
Forum: Extruder Assembly
Topic: Can you detune the extruder to still use poor filament (Skip not shred)
Replies: 6
Views: 1047

Re: Can you detune the extruder to still use poor filament (Skip not shred)

While the M82 command was a bad slicer setting that didn't help; I still could not reach fast speeds without the risk of the filament getting chewed up from the hob gear. Just thought I would follow up to my final solution: 1.) I added an access hole to clean the hob if it started stripping 2.) I re...
by Lucidwolf
Fri Aug 31, 2018 10:16 am
Forum: Extruder Assembly
Topic: Can you detune the extruder to still use poor filament (Skip not shred)
Replies: 6
Views: 1047

Re: Can you detune the extruder to still use poor filament (Skip not shred)

(M82) extruder absolute is a super important command to have in your slicer if the configuration file sets extrusion up as relative (M83)... :lol: The extruder is a bit more forgiving if you don't try to exponentially jam more and more down its gullet. :roll: You wanted to know how i was shredding i...
by Lucidwolf
Wed Aug 29, 2018 12:15 pm
Forum: Calibration
Topic: Delta Arm Calibration for Positional Tolerance
Replies: 2
Views: 948

Re: Delta Arm Calibration for Positional Tolerance

Greetings, On Repitier/Marlin you can set each towers diagonal rod length individually. So you can print a delta tower calibration measure each tower's distance in the X-Y plane use that to calculate a dimensional error to the tower and calculate the corrections for each individual arm. I'm starting...
by Lucidwolf
Wed Aug 29, 2018 11:44 am
Forum: Extruder Assembly
Topic: Can you detune the extruder to still use poor filament (Skip not shred)
Replies: 6
Views: 1047

Re: Can you detune the extruder to still use poor filament (Skip not shred)

Also I forgot to mention at the start of this post that I am trying to learn the machine inside and out what is happening here is not in any way shape or form an issue with the part quality. This printer has out right spoiled me with accurate bed probing, duet controller, these fancy trick arms that...